三葉羅茨風機檢修方法步驟教程！21個細節！熠生輝

　　Three leaf Roots blower maintenance method steps tutorial! 21 details! Radiant radiance

　　羅茨風機拆卸檢修的內容有很多，熠生輝整理了一部分資料供大家進行參考，每個廠家的三葉羅茨鼓風機性能不同，有些步驟也不會相同，這里熠生輝提供給大家，只為供大家學習補充使用，具體的流程請看下圖，如果您看不清楚，可以閱讀圖片下面的文字。

　　There are many contents related to the disassembly and maintenance of Roots blowers. Yishui has compiled some materials for reference. The performance of each manufacturer's three blade Roots blower is different, and some steps may not be the same. Here, Yishui provides them for everyone to learn and supplement. Please refer to the following figure for the specific process. If you are not clear, you can read the text below the picture.

　　1、拆消聲器、潤滑油及冷卻水管

　　1. Dismantle the muffler, lubricating oil, and cooling water pipe

　　2、分離聯軸器，拆開地腳螺絲。

　　2. Separate the coupling and remove the foot screws.

　　3、吊出風機。

　　3. Lift out the fan.

　　4、拆開聯軸器和端蓋。

　　4. Remove the coupling and end cap.

　　5、齒輪間隙，轉子間隙，轉子與墻板間隙轉子與殼體間隙。

　　5. Gear clearance, rotor clearance, rotor to wall clearance, rotor to shell clearance.

　　6、氣封厚度，若厚度磨損較多則要更換。

　　6. The thickness of the gas seal should be replaced if there is significant wear on the thickness.

　　7、拆卸同步齒輪：用專用液壓泵把齒輪拆出。

　　7. Disassemble the synchronous gear: Use a dedicated hydraulic pump to remove the gear.

　　8、依次拆卸軸承，軸承座及氣封。

　　8. Disassemble the bearing, bearing seat, and air seal in sequence.

　　9、拆墻板（拆卸墻板應把風機立起）。

　　9. Dismantle the wall panel (the fan should be erected when dismantling the wall panel).

　　10、吊出轉子。

　　10. Lift out the rotor.

　　11、清理轉子表面灰垢，檢查各部位間隙，并與標準數據比較，是否損壞。

　　11. Clean the dust and dirt on the surface of the rotor, check the clearances between various parts, and compare them with standard data to see if they are damaged.

　　12、清洗其它部件（機殼，墻板)

　　12. Clean other components (casing, wall panels)

　　13、回裝一面墻板，并立起。

　　13. Reinstall one wall panel and stand it up.

　　14、吊入兩轉子，再回裝另一面墻板。

　　14. Lift in two rotors and reinstall the other wall panel.

　　15、回裝氣封，軸承座，軸承。

　　15. Reinstall the air seal, bearing seat, and bearing.

　　16、回裝齒輪，并同時調整轉子的各位置間隙：轉子之間0.35－0.45mm；同步齒輪嚙合間隙0.08－0.16mm。

　　16. Reinstall the gears and adjust the clearances between the rotors at various positions simultaneously: 0.35-0.45mm between rotors; 0.08-0.16mm between synchronous gears.

　　17、然后用液壓泵把齒輪壓入。

　　17. Then use a hydraulic pump to press the gears in.

　　18、測量止推間隙：轉子與止推端墻板間0.3－0.4mm；另外，轉子與傳動端墻板間建議大于另一則0.5mm以上。測量轉子間隙：根據轉子各葉片間間隙（0.35－0.45mm）分別用塞尺測出，轉子與殼體間隙（0.3－0.4mm），轉子與墻板間隙，并記錄下來。

　　18. Measure the thrust clearance: 0.3-0.4mm between the rotor and the thrust end wall panel; in addition, the distance between the rotor and the transmission end wall panel must be greater than another 0.5mm or more. Measure rotor clearance: Use a feeler gauge to measure the clearance between each blade of the rotor (0.35-0.45mm), the clearance between the rotor and the shell (0.3-0.4mm), and the clearance between the rotor and the wall panel, and record them.

　　19、回裝聯軸器和端蓋。

　　19. Reinstall the coupling and end cap.

　　20、就位：就位于原機座，擰緊地腳螺絲。

　　20. In place: located on the original machine base, tighten the foot screws.

　　21、回裝各附屬管線，法蘭螺絲。

　　21. Reinstall all auxiliary pipelines and flange screws.

　　一般三葉羅茨鼓風機維修都是返廠維修，很少有客戶會自己進行維修，如果您有三葉羅茨鼓風機的維修問題，或者需要維修三葉羅茨鼓風機，可以聯系我們的官方客服熱線。

　　Generally, the maintenance of the Three Leaf Roots blower is done by returning it to the factory for repair, and few customers will repair it themselves. If you have any maintenance issues with the Three Leaf Roots blower or need to repair it, you can contact our official customer service hotline.

　　本文由   羅茨鼓風機  友情奉獻.更多有關的知識請點擊  http://www.guangda-co.com/  真誠的態度.為您提供為多維度的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Roots blower For more related knowledge, please click http://www.guangda-co.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.