羅茨風機為您介紹羅茨風造組成。羅茨風機主要由四部分構成：機殼、墻板、葉輪、進出口消音器等。

　　Roots blower introduces the composition of Roots blower. The Roots blower mainly consists of four parts: casing, wall panels, impeller, inlet and outlet mufflers, etc.

　　1、葉輪:是羅茨鼓風機轉動部分，分成二葉和三葉。如今，因為三葉的出氣脈沖小、低噪、運行穩定等眾多優勢，已經漸漸替代了二葉羅茨鼓風機。

　　1. Impeller: It is the rotating part of a Roots blower, divided into two blades and three blades. Nowadays, due to its advantages such as small air pulse, low noise, and stable operation, the three bladed Roots blower has gradually replaced the two bladed Roots blower.

　　2、機殼：主要用于支撐墻板、葉輪、消音器和固定作用。

　　2. Shell: mainly used to support wall panels, impellers, mufflers, and for fixing purposes.

　　3、墻板：主要用于連接機殼和葉輪，并支撐葉輪的轉動，及其端面密封的。

　　3. Wall panel: mainly used to connect the casing and impeller, support the rotation of the impeller, and seal its end face.

　　4、消音器：用于降低羅茨風機因氣旋脈沖而引起的出入噪聲。

　　4. Muffler: Used to reduce the inlet and outlet noise caused by cyclone pulses in Roots blowers.

　　羅茨鼓風機是一種體積式鼓風機，輸送的風量與轉速成比例。葉輪端面與鼓風機前后蓋之間和鼓風機葉輪之間的間隙總是很小。在同步齒輪的推動下，風從鼓風機的進氣口順著機殼內壁輸送到排出的一側。

　　Roots blower is a volumetric blower that delivers air in proportion to its rotational speed. The gap between the impeller end face and the front and rear covers of the blower, as well as between the blower impeller, is always very small. Under the push of the synchronous gear, wind is transported from the inlet of the blower along the inner wall of the casing to the side where it is discharged.

　　今日風機將與大家一起拆解，看看羅茨鼓風機是由什么部件組成的。

　　Today, we will disassemble the fan together to see what components make up the Roots blower.

　　，一套完整的羅茨鼓風機包含:風機主機、共享基座、電機、電機桿、皮帶盤、皮帶蓋、三通、減壓閥、止壓閥、氣壓表、入口消聲器、出口消聲器、抗震接頭、防震墊、配套螺釘?shù)取?/p>

　　A complete set of Roots blower includes: fan host, shared base, motor, motor rod, belt pulley, belt cover, tee, pressure reducing valve, check valve, pressure gauge, inlet muffler, outlet muffler, seismic joint, seismic pad, matching screws, etc.

　　除了配件和電機，羅茨鼓風機主機是技術含量和重要構成部分。一個好的主機頭在使用中噪聲相對較低，風量比較穩定。與其它羅茨鼓風機相比，其使用壽命能長達5年以上。在諸多羅茨鼓風機生產商中，機械技術憑著堅實基礎和強大的生產實力，在羅茨鼓風機設計、制造和銷售層面，變成羅茨鼓風機行業管理者。其生產的羅茨鼓風機合理，風量大，低噪，節能，性能優異，堅固耐用。

　　In addition to accessories and motors, the Roots blower host is a technologically advanced and important component. A good host head has relatively low noise and stable air flow during use. Compared with other Roots blowers, its service life can last for more than 5 years. Among many Roots blower manufacturers, mechanical technology, with a solid foundation and strong production capabilities, has become the industry manager in the design, manufacturing, and sales of Roots blowers. The Roots blower produced by it is reasonable, with large air volume, low noise, energy saving, excellent performance, and durability.

　　羅茨鼓風機主機主要由2組葉輪、一個汽缸、四個軸承、2個齒輪、2個端蓋、一個齒輪罩、2個軸承座和其它部件構成。

　　The Roots blower main unit is mainly composed of 2 sets of impellers, 1 cylinder, 4 bearings, 2 gears, 2 end caps, 1 gear cover, 2 bearing seats, and other components.

　　配件清單圖

　　Accessories List Diagram

　　羅茨風機分解圖

　　Decomposition diagram of Roots blower

　　需要注意的是，羅茨鼓風機可分為兩種類型:真空鼓風機和壓送鼓風機。真空和壓送羅茨鼓風機實質上沒有太大的差別，他們是由主機的電機和配件組成的。不同的是，真空羅茨鼓風機遇有一個真空過濾桶。這是壓送羅茨鼓風機沒有用的。

　　It should be noted that Roots blowers can be divided into two types: vacuum blowers and pressure blowers. There is not much difference between vacuum and pressure fed Roots blowers, they are composed of the motor and accessories of the main unit. The difference is that the vacuum Roots blower has a vacuum filter barrel. This is useless for pressure fed Roots blowers.

　　真空式羅茨風機結構圖

　　Structural diagram of vacuum Roots blower

　　以上是羅茨鼓風機基本結構。如果你想了解更多更多信息，請咨詢風機。大家會給你更豐富詳細的解釋。掌握羅茨鼓風機制造后，通常是羅茨鼓風機維護和應用。羅茨鼓風機運作時要注意查驗:電源、電壓、電流值、壓力、大氣溫度、排氣溫度、軸承溫度、震動、噪聲、油量、污漬水平、皮帶張力等。，并留下記錄卡，這對調研及早發現或出現問題的原因有很大幫助。出口閘閥不能用于調節風量，應改變轉速或增送方法。

　　The above is the basic structure of Roots blower. If you want to learn more information, please consult the fan. Everyone will provide you with more comprehensive and detailed explanations. After mastering the manufacturing of Roots blowers, it is usually the maintenance and application of Roots blowers. During the operation of Roots blower, attention should be paid to checking: power supply, voltage, current value, pressure, atmospheric temperature, exhaust temperature, bearing temperature, vibration, noise, oil level, stain level, belt tension, etc. And leave a record card, which is very helpful for early detection or identification of the causes of problems during research. The outlet gate valve cannot be used to regulate air volume, and the speed or delivery method should be changed.

　　大家在羅茨鼓風機解剖圖前邊的文章中分享過。隨著小系列數據的不斷完善，羅茨鼓風機解剖圖早已分類整理了。先放一張設計解剖圖:

　　Everyone has shared in the article before the anatomical diagram of Roots blower. With the continuous improvement of small series data, the anatomical diagram of Roots blower has already been classified and organized. First, place a design anatomical diagram:

　　這張圖是一張縮小后的小圖，上面有標明的具體內容。由于之前的文章早已提及了，如果你想看大圖和注明的內容，請點擊這里?！鷂→由三葉羅茨鼓風成，下面小編還為大家整理了一張彩色三葉羅茨鼓風機解剖圖，圖為老羅茨鼓風機L型，如圖所示:

　　This picture is a reduced image with specific content indicated on it. As mentioned in the previous article, if you would like to see the large image and the annotated content, please click here. → _ → Created by the Three Leaf Roots blower, the following editor has also compiled a colored anatomical diagram of the Three Leaf Roots blower, which is an L-shaped old Roots blower, as shown in the picture:

　　因為樣式的原因，很多羅茨鼓風機生產商早已對其進行了整改設計。羅茨鼓風造基本一致，但不同的生產商和不同的生產商之間有微小的差別。供參考。下列解剖圖為三葉羅茨鼓風機內部透視框架圖，如下所示:

　　Due to the style, many Roots blower manufacturers have already made improvements to their designs. Roots blower production is basically the same, but there are slight differences between different manufacturers. For reference only. The following anatomical diagram is an internal perspective frame diagram of a three blade Roots blower, as shown below:

　　這可以更立體的展示，葉輪、齒輪、軸承、油箱等零部件能夠清晰的看到。隨著風機數據的不斷完善，還整理了一張四分之一的截面圖，如圖所示:

　　This can provide a more three-dimensional display, where components such as impellers, gears, bearings, and oil tanks can be clearly seen. With the continuous improvement of fan data, a quarter section diagram has also been compiled, as shown in the figure:

　　三葉羅茨鼓風機結構和二葉羅茨鼓風機基本一致，由于羅茨鼓風機還有其他結構類型，如密集式、水冷型等。，并且還有其他構造的解剖圖，可是羅茨鼓風機主體框架圖大部分是這樣的。

　　The structure of the three leaf Roots blower is basically the same as that of the two leaf Roots blower, as there are other structural types of Roots blowers, such as dense and water-cooled. And there are also anatomical diagrams of other constructions, but most of the framework diagram of the Roots blower body is like this.

　　型號介紹:(-200羅茨鼓風機)。羅茨鼓風機采用先進的設計技術和高精密制造。選用內部回流技術、出口降噪技術、三葉擺線葉型、拼裝密集技術等科研開發。髙壓羅茨鼓風機性能可靠，應用范圍廣，密封結構各種類型，滿足氨氣力輸送、粉煤灰輸送、選礦廠、化工、焦煤等其它污染和浸蝕標準。是49客戶～商品在98kPa下。流量范圍：1.63～101m3/min；變壓范疇：9.8～98kPa

　　Model introduction: (-200 Roots blower). Roots blower adopts advanced design technology and high-precision manufacturing. We have conducted scientific research and development on internal reflux technology, export noise reduction technology, three blade cycloid profile, and dense assembly technology. The high-pressure Roots blower has reliable performance, wide application range, and various types of sealing structures, meeting other pollution and erosion standards such as ammonia pneumatic conveying, fly ash conveying, mineral processing plants, chemical industry, coking coal, etc. 49 customers~The product is under 98kPa. Flow range: 1.63-101m3/min; Transformer range: 9.8-98kPa

　　動力傳送方式包含皮帶連接和連軸器連接，靈活方便；鼓風機200羅茨鼓風機壓力平穩，低噪，震動小。壓力可見，便于監管200羅茨鼓風機工作狀態。配件性能優異。集成集中的設計特點使之體型小、流量、以人為中心拼裝方法；鼓風機羅茨鼓風機配備:依據作用不同，200羅茨鼓風機軸承配備既能滿足風機規定，又能達到高質量。200羅茨鼓風機集風機、進出口消音器、電機、過濾器、彈性接頭、閘閥、逆止閥、壓力計為一體。

　　The power transmission method includes belt connection and coupling connection, which are flexible and convenient; The 200 Roots blower has stable pressure, low noise, and minimal vibration. The pressure is visible, making it easy to monitor the working status of the 200 Roots blower. Excellent accessory performance. The integrated and centralized design features result in a small size, high flow rate, and a human centered assembly method; Blower Roots blower equipment: Depending on its function, the 200 Roots blower bearing equipment can meet the requirements of the fan and achieve high quality. The 200 Roots blower integrates a fan, inlet and outlet mufflers, motor, filter, elastic joint, gate valve, check valve, and pressure gauge.

　　本文由 羅茨鼓風機  友情奉獻.更多有關的知識請點擊  http://www.guangda-co.com/  真誠的態度.為您提供為多維度的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Roots blower For more related knowledge, please click http://www.guangda-co.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.